Uncategorized

Hayward PVDF Vertical Immersible Seal-Less Pump 1D1GX0009

March 7, 2020

Hayward 1D1GX0009 Series D & S Vertical Immersible Pump, PVDF, 1 Phase, 1/8 HP, 1″ Suction, 1/2″ Discharge, 115/230 V. PVDF VERTICAL IMMERSIBLE PUMP 1/8 HP 115/230 1PHASE. Hayward 1D1GX0009, PVDF VERT IMMERSIBLE PUMP 1/8 HP 115/230 1PHASE, Seal-Less, Vertical D & S Series, Industrial Pumps.

Brand: Hayward

Manufacturer# 1D1GX0009

Price: $1155.75 $904.94

Product Overview:

The Hayward/Webster- D Series Vertical Immersible Pump, model 1D1GX0009, 1/8 HP, 115/230 Volts, 1 Phase, 1″ Suction, 1/2″ Discharge, 12 lbs., and is made of PVDF. These products are vertical seal-less, immersible, plastic pumps that are designed for rugged chemical duty applications. They handle a wide range of corrosive and ultra-pure liquids.

D Series Vertical Seal-Less Immersible Pumps
D Series vertical pumps are rugged, chemical duty pumps for handling a wide range of corrosive liquids.

KEY FEATURES
CPVC, Natural PP and PVDF
No Seals to Leak or Replace
PTFE Fume Barrier
FPM Elastomer
Optional Inlet Screens

OPTIONS
Comple
In-Tank Filtration
Inlet Screens
EPDM Elastomer
Impeller Trim Variations
Explosion Proof Motors
Washdown Motors
575V Motors
S-J Type Electrical Cord

MATERIALS
CPVC Cell Class 23447 per ASTM D1784
PP per ASTM D4101
GFPP Cell Class 85580 per ASTM D4101
PVDF

Technical Specifications

Pump HeadPVDF
Pipe ConnectionThreaded Connections
ShaftStainless Steel Shaft with Non-Metallic Sleeve
SealPTFE Fume Barrier Protects Motor and Bearings, FPM O-Rings
PerformanceFlow Rates from 2 to 17 GPM with TDHs up to 18 Feet
MotorsSingle Phase Motor with 1/8 HP, 115/230 VAC has Heavy Duty TEFC, Epoxy Painted Construction and is Rated for Continuous DutyService.The Motor Features a 1/2″ Diameter Extended Stainless Steel Shaft and Sealed Ball Bearings with “Slinger” Lip Seal.
Hp Rating1/8 HP
Inlet1” MNPT
Discharge1/2” FNPT
01720-375 Flojet

Flojet 01720-375 Strainer

March 5, 2020

Flojet- Strainer with 3/8” Female NPT Inlet and 3/8” Female NPT Outlet, In-Line Design, Course 20 Mesh Stainless Steel Screen   Product Details 0.5More Info:  01720-375S, 01720375S

Brand: Flojet

Manufacturer# 01720-375

ESIN# ES00010452137

Price: $29.89

Product Overview

APPLICATIONS / CHARACTERISTICS
Strainers for In-Line Applications. FDA Approved for Potable / Drinking Water.Strainer Body made of Polypropylene with Clear Polysulfane Cap and Buna-N FDA O-Rings.
Suitable for Fresh or Salt Water use.
Easily Cleaned with See Through Thread-On Cap.Course 20 Mesh Screens are typically used for Washdown, Bilge and Toilet Rinse Applications.
Fine 40 Mesh Screens are typically used for Potable / Drinking Water Applications.Maximum Flow Rates:
With 3/4″ Hose Barb Fittings: 7.0 GPM (27 LPM)
With 1/2″ Hose Barb Fittings: 4.0 GPM (15 LPM)
With 3/8″ Hose Barb Fittings: 2.1 GPM (8 LPM)Maximum Water Temperature: 160F (70C)
Maximum Pressure: 70 PSI (5 bar)The Strainers that are Equiped with a “Direct Plug-In Quad Port” will fit into the Snap-In Quad Ports on Flojet Diaphragm Pumps and Jabsco Diaphragm Pumps sized under 6 GPM.**Please base your purchase on the description of the strainer and not on the photo of the strainer. The photos are not all exactly accurate.Click here for Snap-In Quad Port Fittings:
50200-2311 Jabsco

Jabsco 50200-2311 Clutch Pump, 44.5 gpm, 1-1/2″ BSP to BS21 Ports, 24 VDC Clutch, No Motor

March 4, 2020

Jabsco- Clutch Pump, 1-1/2″ British Standard Pipe Threads, Neoprene Impeller, 24V, 1 Groove “B” Belt Pulley. Jabsco electro-magnetic 44.5 gpm clutch pump having 1-1/2″ BSP to BS21 inlet size and 1-1/2″ BSP to BS21 outlet size features 1500 rpm motor speed

Brand: Jabsco

Manufacturer# 50200-2311

ESIN# ES00010450386

Price: $1186.54

Product Overview

Jabsco 50200-2311 Clutch Pump

Features

Jabsco electro-magnetic 44.5 gpm clutch pump having 1-1/2″ BSP to BS21 inlet size and 1-1/2″ BSP to BS21 outlet size

  • Constructed from marine quality bronze and stainless steel for ruggedness and reliability
  • Easy to service and maintain
  • Inexpensive to buy and operate
  • Will tolerate abrasive wear
  • Handles hard and soft solids without clogging
  • Can pump in either direction
  • Will not airlock
  • 1-B belt pulley
  • Replaceable wearplate
  • Self-priming from dry up to 2.4 m
APPLICATIONS / CHARACTERISTICS
Electric Clutch Pedestal Mount Pump. British Standard Pipe Threads.Constructed from marine quality bronze and stainless steel for ruggedness and reliability. Easy to service and maintain. Inexpensive to buy and operate. Will tolerate abrasive wear. Handles hard and soft solids without clogging. Can pump in either direction. Will not airlock. Self-priming from dry up to 2.4m (7.8ft).

The Jabsco 24V foot mounted clutched pump is suitable for bilge and deckwash applications. The pump features 1-1/2″ BSP female threaded ports and measures 200mm long with a 180mm pulley diameter (1B pulley) and 152mm across the ports. The Jabsco clutched pump is capable of pumping 195 litres per minute (43 gallons) at 3 metres total head.

This heavy duty bilge and deckwash pump has a bronze constructed body, stainless steel shaft, mechanical shaft seal and comes with a neoprene impeller fitted for maximum performance when pumping clean or slightly contaminated water. A nitrile impeller may be fitted for use with oily water applications. The pump can self-prime up to 3 metres of vertical lift and is tolerant to moderate amounts of suspended solids.

Technical Specifications

Brand Name: Jabsco
MFR Part Number: 50200-2311
UNSPSC: 40151500
Item: Clutch Pump
Type: Electro-Magnetic
Series: 50200
Flow Rate: 44.5 gpm
Inlet Size: 1-1/2 in BSP to BS21
Outlet Size: 1-1/2 in BSP to BS21
Impeller Type: Flexible
Bearing Type: Ball, Twin Row
Body Material: Bronze
Impeller Material: Neoprene
Shaft Material: Stainless Steel
Seal Type: Mechanical
Seal Material: Carbon/Ceramic
Dimensions: 190 mm Length x 178 mm Width

70-7214 Wilden

Wilden SD1-PMP-TF-TV Diaphragm Pumps 70-7214 Polypropylene NPT PTFE Elastomers

March 3, 2020

Wilden 1″ Surge Dampener, Polypropylene NPT PTFE Elastomers

Brand: Wilden

Manufacturer# 70-7214

ESIN# ES00000043010

Price: $1116.00

Product Overview

SD1-PMP-TF-TVWilden® Equalizer® Surge Dampener SD Series creates laminar process flow by reducing and/or eliminating pump pulsation. SD Equalizers do this by using the same air supply as the pump to counter the pressure changes within the system. When installed properly using the same air supply as the pump, SD Equalizers equalize the correct air pressure to match variations in liquid flow or discharge pressure.

  • Lowers system maintenance costs
  • Protects in-line equipment
  • Self-adjusts to varying system pressure

Technical Specification

SkuSD1-PMP-TF-TV
Wetted Path Material FamilyPlastic
Upper Temperature Limit225 F
Seats SealFKM Encapsulated PTFE
Max Air Inlet Pressure125 psi
Product Weight17.5 lbs (7.88 kg)
Primary Diaphragms MaterialPTFE
Lower Temperature Limit40 F
Connection Outlet Size1″ (25 mm)
Product ModelSD1
Literature Tag30
BrandWilden
Backup Diaphragms MaterialNeoprene
Connection TypeNPT
MaterialsPolypropylene
Sizes1″ (25 mm)

ARO H254SS-120-A

ARO H254SS-120-A Solenoid Air Control Valve,1/2 In,120VAC

March 3, 2020

H254SS-120-A ARO Pneumatic Valves. Port Size 1/2 in NPT, Actuation/Return Solenoid/Spring, Coil Volage 120V AC or DC, Current Type AC. Solenoid Air Control Valve, Air Valve Type 3-Way, 2-Position, Actuator/Return Solenoid/Spring, Body Style Body Ported, Pipe Size 1/2″, Voltage 120VAC, CFM 85, Coefficient of Volume 2.4, Electrical Connections DIN Connectors, Shifting Technology Solenoid/Pilot, Power Consumption 4.8W, Pressure Range 30 to 150 psi, Ambient Temp. Range -10 Degrees to 180 Degrees F, Overall Height 3-1/2″, Overall Length 6-1/4″, Overall Width 4″, NEMA Classification NEMA 4

Brand: ARO

Manufacturer# H254SS-120-A

ESIN# ES00000044850

Price: $461.51 $438.43

Product Overview

Air Control Actuation Valves

3-way valve controls air supply to pump. Activation starts pump, deactivation cuts off air supply to pump and exhausts air from motor, which prevents stalling.

H series Valves Several Styles and Options

  • H-Series Valves feature high-flow and fast response.
  • Numerous Styles and Options.
  • Several Actuator Styles.
  • 3-Way and 4-Way 2-position Poppet Valves.
  • Override is not available with “H” Series Valves
  • Electric: 3-Way Single Solenoid, 4-Way Solenoid/ Internal Pilot, 4-Way Double Solenoid
  • Pneumatic: 3-Way Pilot/Spring, 4-Way Double Pilot, 4-Way Manual Bleed, 4-Way Pilot/Internal Pilot

Comprehensive Valve DesignDurable Valve Body

Valve body is die-cast Zinc, with a zinc chromate coating for added corrosion resistance in harsh environments.Superior Performance

Large, unrestricted air passages produce high flow and fast response times.Superior Design

3-Way valves feature a single poppet. 4-Way valves have two simultaneously driven poppets to provide the 4-way function.

Solenoid Air Control Valve, Valve Ways and Positions 3-Way/2-Position, Voltage 120VAC, Valve Actuator / Return Solenoid / Spring, Pipe Size 1/2 In., Max. CFM – Valves 85.00, Operational Pressure Range 30 to 150 psi, NEMA Classification NEMA 4, Body Style Body Ported, Coefficient of Volume 2.4, DIN Connectors Electrical Connections, Shifting Technology Solenoid/Pilot, Power Consumption 4.8W, Ambient Temp. Range -10 Degrees to 180 Degrees F, Overall Height 3-1/2 In., Overall Length 6-1/4 In .

Technical Specification

Body Style3 Way Side Ported
Port Size1/2 in NPT
Actuation/ReturnSolenoid/Spring
Coil Volage120V AC or DC
Current TypeAC
Series Data
TypePneumatic Valve
Item: Solenoid Air Control Valve
• Valve Ways and Positions: 3-Way/2-Position
• Voltage: 120VAC
• Valve Actuator / Return: Solenoid / Spring
• Pipe Size: 1/2″
• Max. CFM – Valves: 85.00
• Operational Pressure Range: 30 to 150 psi
• NEMA Classification: NEMA 4
• Body Style: Body Ported
• Coefficient of Volume: 2.4
• Electrical Connections: DIN Connectors
• Shifting Technology: Solenoid/Pilot
• Power Consumption: 4.8W
• Ambient Temperature. Range: -10 Degrees to 180 Degrees F
• Overall Height: 3-1/2″
• Overall Length: 6-1/4″
• Overall Width: 4″
• Pneumatic Valves Product Group: Solenoid Air Control Valve
Features:• 1/2″ Solenoid 120vac 3 Way Air Control Valve
KeywordsPneumatics,H254SS-120-A,32142069

Solenoid Air Control Valve, Air Valve Type 3-Way, 2-Position, Actuator/Return Solenoid/Spring, Body Style Body Ported, Pipe Size 1/2″, Voltage 120VAC, CFM 85, Coefficient of Volume 2.4, Electrical Connections DIN Connectors, Shifting Technology Solenoid/Pilot, Power Consumption 4.8W, Pressure Range 30 to 150 psi, Ambient Temp. Range -10 Degrees to 180 Degrees F, Overall Height 3-1/2″, Overall Length 6-1/4″, Overall Width 4″, NEMA Classification NEMA 4WARNING: California ResidentsThis product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. 

170M-A82 Oberdorfer

170M-A82 OBERDORFER Pump, Centrifugal Pump with Motor, Factory New!

February 23, 2020

Oberdorfer – 170M-A82 Centrifugal Pump. Inlet 3/4″ – Outlet 3/4″ – 20 GPM – 24VDC – 3480 RPM – 1/10HP – Mechanical Seal Type – 7 lbs Weight. Rudge corrosion resistant bronze construction. The mechanical seal is a carbon and ceramic mechanical rotary face type for positive sealing. The stator is made from molded nitrile. Compact and Light.

Brand: Oberdorfer
Manufacturer# 170M-A82
ESIN# ES00010450166
Price: $687.70

Product Overview

Oberdorfer Centrifugal Pump Model# 170M-A82

Product Information

These Oberdorfer™ centrifugal pumps have a single open vane rotating impeller. Liquid enters at the center and is thrown outward radically by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently, a relief valve is not required.

The flow of these pumps can be conveniently controlled by a throttling valve in the discharge line. Horsepower demand will decrease as the pressure increases. Maximum horsepower occurs with a wide open discharge.

The lip seal is Nitrile with stainless steel spring reinforcement on a stainless steel motor shaft. The seal is friction press fit in a machined housing counter bore. Excessive system pressures above 15 PSI are not recommended as the seal could be forced out of the pump housing.

FEATURES

  • Rugged Corrosion Resistant Bronze Construction
  • Compact & Light
  • Nitrile Lip Seal STD; Optional fluoroelastomer Lip
  • TEFC Motors With Corrosion Resistant Passivated 316 SS Shafts
  • 1/10 HP Permanent Magnet 12V, 24V, 32V DC Motors
  • Rubber Base Grommets For Vibration Dampening
  • Insulated Leads
  • 1/13 HP Permanent Magnet 12V DC Motor (A95)

Ideal for:

  • Marine Air Conditioning
  • Engine Block Temperature Control
  • Radiator & Heat Exchanger Circulation
  • Baitwell Circulation

DRIVE

One of the outstanding features of this pump and motor unit is its compact D.C. motor size. Although small, adequate motor power is available. Motors are available in 12, 24 and 32 VDC.

LIQUIDS & TEMPERATURES

This pump is more than capable of pumping water, water solutions, and a wide range of commercial chemicals. Viscous liquids with a maximum viscosity of 2000 Saybolt Seconds Universal can be pumped. However, when pumping viscous liquids (as compared with water) a reduction in flow and pressure occurs and the required horsepower increases. Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity. Questions about the chemical compatibility of special liquids should be referred to the factory.

SUCTION LIFT

These pumps are not self priming. They must be installed below the liquid level so that the liquid flows to the pump by gravity (flooded suction). However, if a foot valve is used at the beginning of the suction line, and all air is bled from the pump by manual priming, the pump will lift on the suction side up to 15 feet. Such a system relies entirely on the non-leaking foot valve for starting capability.

FEATURES

Pump Body:Bronze

Ports:3/4″ NPT

Flow:12 GPM Max

Pressure:7 PSI Max, 17 feet of head

Impeller:Centrifugal

Shaft Seal:Buna Lip Seal Standard, Optional Viton lip

Shaft:Corrosion resistant passivated 316 SS Shaft

Motor / Drive:TEFC Motors 1/10 HP Permanent Magnet 12V, 24V, 32V DC Motors.
Rubber base grommets for vibration dampening.
Available with 1/13 HP Permanent Magnet 12V DC Motor (A95).  

APPLICATIONS / CHARACTERISTICS

BRONZE CLOSE COUPLED CENTRIFUGAL PUMP Ideal for: Marine Air Conditioning, Engine Block Temperature Control, Radiator and Heat Exchanger, Circulation Baitwell Circulation.

MVS1PA-PC050 Pulsatron

MicroVision Controller of Pulsatron Pump with Voltage 115 volt

February 22, 2020

Pulsatron Pump MVS1PA-PC050 Microvision Controller. Relay & Power Wiring : Prewired w/Power Cord and Pigtails for 115 VAC, Standard Panel & Flow Assembly

Brand: Pulsatron

Manufacturer# MVS1PA-PC050

ESIN# ES00000087454

Price: $1819.00

Product Overview

PULSAtron

The PULSAtron product line has evolved into a philosophy of design that continues to set the standards for the entire industry. Our engineers have developed a guided check valve system with a proven ‘seat and ball’ design that ensures reliable and accurate metering year after year.

Industrial Construction
Our fin cooled Solenoid enclosure dissipates heat ensuring that the pressure handling capability of the pump can be maintained. The thermally protected solenoid protects the pump from seizing up in extreme heat conditions with an automatic reset feature allowing the pump to resume operation up on cool-down. All PULSAtrons are tested and rated under hot conditions guaranteeing that the flow and pressure ratings meet the specifications. There are no standards when it comes to the type of chemicals our pumps may encounter. Therefore we offer a variety of wet-end materials that the customer can choose from. Every pump is ‘configured to order’ with the customer designated wet-end materials that match the chemical requirements of the target application.

Application Expertise
With more than 10 years of product evolution, the PULSAtron family continues to set the standard with the Degas Five Function Valve. PULSAtron can handle a variety of gaseous solutions. The PULSAtron family consists of seven unique series with 78 flow and pressure envelops to select from. Most models include our standard bleed valve assembly, foot strainer, injection valve and tubing. No matter what your application is, choose the PULSAtron that is right for you.PULSAtron MicroVision Controller

The MicroVision Controller series features is innovative Toroidal sensor technology. Toroidal sensors are not susceptible to fouling and eliminate the need for routine cleaning and calibration. The MicroVision controller comes standard with selectable timer, Dry contact/ Hall Effect water meter input, dual biocide with pre-bleed, lockout, inhibitor interface, and four programmable start times per biocide, 4-20mA output, dry contact alarm output and 3 drum level inputsFeatures :

  • Selectable timers
  • Digital inputs
  • Outputs
  • Simple Programming – Intuitive menu with soft keys touch pad
  • Toroidal Probe – No calibration required
  • Easy installation and easy to use
  • Heavy duty enclosure
  • Languages – English / Spanish / Portuguese

Technical Specification

VOLTAGE115 volt
RELAY & POWER WIRINGPrewired w/Power Cord and Pigtails for 115 VAC
PANELStandard Panel & Flow Assembly
SUFFIX CODESUFFIX CODE
Sensor Cable Length50 Feet (15.2m)
Series Data
EnclosuresNEMA 4X / IP65
Flow Switch Pressure125 psi / 8.6 bar
Flow Switch Temperature122°F / 50°C Max
Conductivity Range0-9,999 μS/cm
Power Input90 VAC – 50/60HZ – 5A, 250 VAC – 50/60 HZ – 5A
Controller DisplayLCD
TimersSelectable Limit, Percent, % Post Bleed With Limit, Water Meter, Dual Biocide Timers
Outputs4-20 mA Isolated Analog, Dry Contact Alarm, Bleed – Solenoid valve or motorized ball valve
InputsFlow Switch, 3 Drum Level, Dry Contact Water Meter, Hall Effect
Flow Switch Activate Flow RateApprox. 1 gpm/3.78 lpm
Average Current Draw5 Amps Max
ControlsBleed: Solenoid valve or motorized ball valve, Feed: Inhibitor, Biocides: Dual biocide with pre-bleed – Lockout – Inhibitor interface – Four programmable start times per biocide
Product OptionsPrewired , Flow Assembly , Standard Panel and Flow Assembly , Panel Mounted with , Pumps Cable Length
AccessoriesCorrosion Coupon Racks, Metering Pumps, Motorized Ball Valves , Solenoids , Water Meters

Application Expertise
With more than 10 years of product evolution, the PULSAtron family continues to set the standard with the Degas Five Function Valve. PULSAtron can handle a variety of gaseous solutions. The PULSAtron family consists of seven unique series with 78 flow and pressure envelops to select from.  Most models include our standard bleed valve assembly, foot strainer, injection valve and tubing.  No matter what your application is, choose the PULSAtron that is right for you.

0115-0007-0400 March

March 0115-0007-0400 Centrifugal Magnetic Drive Pump

February 19, 2020

March 0115-0007-0400 Magnetic Drive Pump 1U-MD Series 1. MAX Flow 3 GPM / 9 LPM, Horse Power .005 HP / .003 KW, Electrical 115V 50 / 60HZ

Brand: March

Manufacturer# 0115-0007-0400

ESIN# ES00000085488

Price: $246.00

Product Overview

Series 1

Liters per minute (LPM) and Meters (M) are given when run at 50HZ, except when pump is equipped with Air or DC motors.1A-MD-3/8 Mag Drive Pump

March Pump’s industrial 1A-MD-3/8 is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.5 Feet (or around 2PSI). The 1A-MD-3/8 pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless steel, and Ceramic Magnet. When submerged, Epoxy, Noryl, and the SJT Cord are also in contact with the solution. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.005 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 160 Celsius in open air, or 87 Fahrenheit or 71 Celsius if submerged. The March 1A-MD-3/8 centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals. To determine if the March 1A-MD-3/8 is suitable for your application, please contact March Pump.Option

Housings: Polypropylene or Carbon Filled Kynar
O-Ring: Buna N, Viton, Teflon, or Ethylene Propylene
Shaft: Ceramic or 316 Stainless Steel
Impeller: Nylon or Carbon Filled Kynar
Stainless Steel Base AvailablePerfect for Applications Including

Applications for the 1A-MD-3/8 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.Great for Chemicals Including

The 1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals. The 1A-MD-3/8 may have been modified to handle these chemicals. Please contact March Pump to review your application before using the 1A-MD-3/8 for any of the above listed chemicals.

Technical Specification

Unit System60Hz / 50Hz
Max Flow3 GPM / 9 LPM
Max Head4.6 FT / 1.0 M
Horse Power.005 HP / .003 KW
Electrical115V 50 / 60HZ
SubmersibleYes
Pump TypeCentrifugal Mag Drive
InletScreen
Outlet1/4″MPT
Wet End MaterialPolypropylene
Hayward SB1200STE

Hayward SB1200STE Series SB Simplex Basket Strainer

February 18, 2020

Hayward – SB1200STE 2″ PVC Simplex Basket Strainer w/EPDM o-rings; socket/threaded end connections. End Cover.

Brand: Hayward

Manufacturer# SB1200STE

ESIN# ES00000087655

Price: $574.60 $554.39

Product Overview

SB Series Simplex Basket Strainers

Product Description

Available in sizes 1/2″ – 4″ in PVC, CPVC, GFPP Black, GFPP Platinum and Eastar® materials. Seals are FPM or EPDM with either socket, threaded or flanged end connections. Each strainer comes with a standard plastic basket. Other basket materials available such as SS316, Monel and Hastelloy available upon request. See Basket Replacements.

Features :

  • NSF/ANSI 61
  • PVC, Corzan CPVC and Eastar
  • Ergonomic Hand-Removable Cover
  • In-Line or Loop Connections
  • External Cover Threads
  • Integral Flat Mounting Bases
  • PVC or Corzan CPVC Baskets Standard

Options :

  • Stainless Steel, Monel and Hastelloy Strainer Baskets
  • Pressure Differential Gauge and Switch
  • Baskets Available with Mesh Liner

Applications :

  • Water & Wastewater Treatment
  • Chemical Processing
  • Food & Beverage
  • Swimming Pools & Water Parks
  • Aquaculture
  • Aquarium & Zoo Service
  • Pharmaceutical
  • Pulp & Paper
  • Landfill Service
  • Marine & Corrosive Environments
  • Metal Finishing & Plating

When pipeline system components require protection from dirt and debris and the line can be shut down for basket cleaning, a Hayward All Plastic Simplex Basket Strainer is the ideal choice. Unwanted particles are removed as the process media passes through a perforated strainer basket contained inside the strainer body. The basket traps the unwanted material while allowing the process media to flow freely.

Available in sizes 1/2 inch to 4 inch in PVC, CPVC, GFPP Black, GFPP Platinum and Eastar® materials. Seals are FPM or EPDM with either socket, threaded or flanged end connections. Each strainer comes with a standard plastic basket. Other basket materials available such as SS316, Monel and Hastelloy available upon request. See Basket Replacements.

Technical Specification

Size (in)2
Body MaterialEPDM
SealPVC
End ConnectionSocket/Threaded
Pressure Rating150 PSI @ 70°F Non-Shock
Standard Perforation (in)1/8
ARO LP3008-1

ARO LP3008-1 Grease Pump System

February 15, 2020

LP3008-1 3″ Air Motor Grease Pump Package.

Brand: ARO

Manufacturer# LP3008-1

ESIN# ES00000086686

Price: $830.00

Product Overview

LP3008-1 Grease Pump System

The Ingersoll Rand ARO LP “Thunder Series” grease pump System deliver unmatched industrial performance when pumping a variety of viscous greases.

Specifications:

  • 3″ Diameter Air Motor, Grease Pump System
  • Pump Model: LM2305E-21-B
  • Drum Cover: 94420
  • Hose: 624201-10
  • Follower Plate: 640095-2-B
  • Handle: 94334
  • Adapter: 76493

Features and Benefits:

  • Patented design reduces pulsation, improves flow, and extends service life
  • Stall free, ice free motor with tough durable housing
  • Integrated muffler for quiet operation
  • Easy to service design requires 50% fewer repair parts than competitive models
  • No special tools required for assembly and disassembly
  • No fragile trip rods or pins
  • Backed by a five year warranty